The idle end sensor signals the limit of travel far from the motor. IES2-24 is an idle-end sensor...

The idle end sensor signals the limit of travel far from the motor. IES2-22 is an idle-end sensor...

The idle end sensor signals the limit of travel far from the motor. IES2-20 is an idle-end sensor...

The idle end sensor signals the limit of travel far from the motor. IES2-16 is an idle-end sensor...

12" idle end sensor (also known as the far end sensor) for TigerStop. The idle end sensor signals...

10" idle end sensor (also known as the far end sensor) for TigerStop. The idle end sensor signals...

The idle end sensor signals the limit of travel far from the motor. IES2-08 is an idle-end sensor...

The idle end sensor signals the limit of travel far from the motor. IES2-06 is an idle-end sensor...

The idle end sensor signals the limit of travel far from the motor. IES2-04 is an idle-end sensor...

Replacement cover for the Amplifier (AMP6).

his is a replacement end cap for the Amplifier (AMP6).

This is the bearing for the TigerStop motor mount.

The Motor End Sensor (MES2) signals the limit of travel near the motor. It is compatible with Tig...

This pulley is compatible with TigerStops using a 32mm (1.26") width belt. It also ships with a r...

igerStop Replacement Motor Kit. This kit includes the following items: Motor Mount Motor End Pull...

The Motor Encoder Cable connects motors to the Amplifier (AMP6) in a TigerStop, TigerFence, or Ti...

This rotary Encoder works with TigerStop, TigerFence, and TigerCrossCut. The cable connecting the...

The I/O panel interfaces with peripheral devices including barcode scanners, printers, clamps, an...

The amplifier (AMP6) is the circuit board driving the motor in most TigerStop positioners. AMP6 i...

The 10 foot (3 meter) Metal Value pack is for TigerStop machines up to 12 feet overall length (TS...

The 20 foot (6 meter) Metal Value pack is for TigerStop machines up to 22 feet overall length (TS...

Dust seal strip helps keep dust and debris out of the TigerStop beam. Dust seal strip is ordered ...

The Idle End Cap is a plate that covers the end of the TigerStop extrusion that is far from the m...

The Idle End Carriage/Far End Carriage is for TigerStops using a 32mm (1.26") width belt. It cont...

The idle end pulley is for TigerStops using a 32mm (1.26") width belt. It is compatible with the ...

The internal carriage connects the TigerStop belt inside the beam to the flip away outside of the...

The Flip Away is the external portion of the TigerStop carriage. It provides two T-slots for moun...

The Center Pusher is an attachment for the TigerStop, used for pushing material on center. The pu...

The Miter Gauge (MG) is an attachment for the TigerStop, intended for applications requiring a 45...

The extended miter gauge is an attachment for the TigerStop, intended for applications requiring ...

This hard plastic trim fits snugly in the T-slots on TigerStop extrusions, and is sometimes used ...

Locking Handle (includes handle, bolt, & washer). The Locking Handle is used on various pusher fo...

The extended pusher foot is a flat pushing attachment for the TigerStop. The pushing surface is 3...

This is a flat pushing attachment for the TigerStop. The pushing surface is roughly 4.0 by 0.75 i...

Flat pushing attachment for the TigerStop. The pushing surface is 6.5" x 3", and can be adjusted ...

Flat pushing attachment for the TigerStop. Pushing surface 10" x 3", can be adjusted 6" - 25" bey...

This Universal Hinge Bracket replaces part numbers below. WHI1000-0006-1 WHI1000-0006-2 WHI021...

Shipping not included.

Shipping not included.

Shipping not included.

Shipping not included

Shipping not included

Shipping not included.

For model 212R only Shipping not included.

For model 212 only. Shipping not included.

Shipping not included.

Shipping not included.

Shipping not included.

For model 212 and 216 only. Shipping not included.

Two Hand Control Non Tie Down Sometimes referred to as a "Double Palm" button. Shipping not inc...